Lawn Tractor Oem Parts
Motorcycle and Atv Cylinder Rebuilding Options
Recent History of Cylinder Types
The oldest and most common method of cylinder design is a cast iron block that is machined with a cylindrical bore directly from a solid casting. There is also a cast iron block that incorporates a sleeve that is pressed into the iron block. Generally iron block motors weren’t very successful in small engines. Most small engines were used in vehicles and equipment that needed to be light and mobile. This made cast iron blocks undesirable for this purpose. There were a lot of single cylinder motors used in lawn mowers, construction equipment, scooters, small tractors and small motorcycles that used cast iron block motors in the early years. These began to disappear in the 60’s and they were replaced by aluminum block motors with cast-in iron liners. This opened the door for new lightweight motors that could be used in many more applications and in bigger displacements than ever before. This was accomplished by placing a cast iron sleeve into the mold before the molten aluminum was poured into the mold. This made the sleeve an integral part of the cylinder block. The sleeve usually had locking rings or flanges around the outside to prevent it from slipping in the casting as the engine expanded from the heat generated by the combustion process. A major problem occurred often when air pockets would develop during the casting operation around the sleeve. This caused hot spots and often caused premature engine cylinder failure.
There is another type of aluminum block with a cast iron sleeve that wasn’t cast-in; it is installed in the block after casting. The cylinder bore of the aluminum block is machined to 3-5 thousands of an inch less than the sleeve diameter, block is then heated to around 600 degrees Fahrenheit, and the sleeve is dropped in. When the block cools the sleeve is held in place by the interference fit and the flange at the top or bottom of the cylinder. This cylinder can be rebuilt by simply re-heating the block to 600 degrees and removing the old sleeve and replacing it with a new one. Of course the finish bore will have to be machined to size and honed.
Near the end of the last century it was discovered that you could make a mold pattern using a computer aided molding system out of Styrofoam. This made it possible to have precise duplicate patterns of a particular cylinder that you wanted to mold of aluminum.
These are placed in a mold made of sand, molten aluminum is then poured slowly into the mold melting and replacing the Styrofoam pattern. This process is called total loss mold casting. Now all they have to do is a little milling and drilling, plate the bore and hone to size. For the two stroke market the best part of this is the finished product is an identical copy of the original. The factories love this because it just eliminated a whole lot of assembly line workers. No more absenteeism, no health insurance or pensions, and no coffee breaks. As far as the consumer goes they get a cylinder that doesn’t need a lot porting before they can be competitive.
There are a lot of four stroke motors that use aluminum blocks and aluminum sleeves that are plated a variety of hard finishes. These sleeves can be removed and replaced. The replacement sleeve can be either iron or aluminum. If you want an aluminum sleeve it will have to be plated after installing otherwise it won’t be true and round.
There are several types of plating that has been used over the years, and the companies doing plating guard their formulas carefully. The finish in the early years was a simple chrome or hard chrome electro-plating. The plating was generally only a few thousands of an inch thick. If it was more than about ten thousands of an inch thick it was prone to chipping or flaking because of heat expansion and contraction. In the early seventies Electrofusion became popular. Electrofusion was different from electroplating in as much as it was a fusion process instead of electroplating. Next there was ceramic composites and Boron. All of these perform in about the same way as far as wear and durability. Then there was Nikasil. Nikasil was a new plating formula of nickel-silicon-carbide. It was harder than the others that came before it. For years you couldn’t get a cylinder re-plated when you damaged one, the only way to get going again was to buy a new one. Now you can choose from many companies doing their own version of Nikasil.
Now let’s look at a person’s choice of repair or rebuilding methods for their Motorcycle, ATV, Snowmobile, Personal Watercraft, or Outboard. You can have your Nikasil or other plated cylinder re-plated (or some called it re-coated). This includes the composite types.
Or you can have it sleeved with a hardened alloy steel or cast iron (when you add alloys to iron its considered steel). If your cylinder has an iron sleeve already, whether it’s cast-in or not, you’re only real choice is replacing it with another sleeve or a sleeve liner.
Let’s assume you’re an avid racer and race 25 weekends a year, you’re going to need a rebuild of your cylinder by the end of the year no matter what type cylinder you have. If it is a plated type cylinder you have three choices. 1- buy a new cylinder for $500-600 for the top end and expect to do the same next year. 2- re-plate it for about $300-400 with piston kit and gaskets and figure on doing it again next year. 3- have it sleeved for about $250-350 with piston kit and gaskets and next year have it bored (most models) to the next size for about $55 plus piston kit and gaskets.
A properly sleeved cylinder will perform as well as any plated cylinder. A properly sleeved cylinder is one that has the proper interference fit, proper pre-sleeve bore finish, accurate flange machining, and sleeve made from the proper alloys. The most popular sleeve is the Moly 2000 chrome-moly iron. The proper boring and honing to match the piston clearance requirements goes without saying.
Pros and Cons
Re-Plated Cylinder Bore
Pros
• Small advantage in heat transfer
• Slightly better wear factor
• Somewhat lower co-efficient of friction
• Weighs a few ounces less
Cons
• Costs slightly more
• Can’t be bored when damage occurs
• More fragile
• Can flake and peel
Iron Sleeved Cylinder Bore
Pros
• Costs less
• Boreable for future over sizes
• Honeable to keep bore true and proper ring seal
• Can be worked with common tools
• Can be replaced when needed
Cons
• Slightly slower heat transfer
The Bottom Line
Both systems perform equally well when professionally done, so it really comes down to economics. You can expect a sleeved cylinder to give more life for the money. Re-plated cylinders are as close to original as you can get. So if you’re happy with your OEM plated cylinder you should have it re-plated. If not have it sleeved by a company that has the reputation, experience, and warrantees to protect your investment. http://kustom-kraft.com
About the Author
Cub Cadet 128 Puller Project Part 1
|
|
OEM John Deere 56 Riding Mower Parts Catalog 1974 $12.95 |
|
|
OEM John Deere 57 Riding Mower Parts Catalog 1976 $9.95 |
|
|
OEM John Deere 60 Lawn Tractor Parts Catalog 1976 $14.95 |
|
|
OEM John Deere 56 Riding Mower Parts Catalog 1972 $12.95 |
|
|
REPLACEMENT LAWN TRACTOR DECK LIFT CABLE MURRAY OEM PART NO. 300341 / 325007 $11.75 |
|
|
Bolens Lawn Mower Vintage Tractor Parts Brake Block 1724192 OEM $20.00 |
|
|
MURRAY 37x114 OEM Lawn Tractor Belt Motion Drive Part $15.95 |
|
|
37X62 37X62MA OEM MURRAY DRIVE BELT RIDING MOWER PART $29.99 |
|
|
NOS Discontinued OEM Roper/Electroux/AYP Brake Rod Lawn Tractors Part# 110437X $31.36 |
|
|
Briggs & Stratton 491588S Flat Air Filter Cartridge $2.94 Brand New factory sealed Briggs and Stratton OEM FILTER-A/C CARTRIDGE. Current 2011 Briggs and Stratton part, Subject to availability from Briggs and Stratton. If not in stock you will be notified within 1 business day.. Check your Owners/Parts manual for correct application and fit. This is the current part description provided by the Original Equipment Manufacturer (OEM). To confirm your parts f... |
|
|
Oregon Gator Mulcher 3-N-1 Lawn Mower Blade For Toro 22-Inch Recycler 94-907 96-607 $11.59 BLADE, GM BLADE TORO 22IN... |
|
|
Oregon 30-031 Paper Air Filter Tecumseh Replacement Part 36905 2-3/4-inches by 1-3/4-inches by 2-7/8-inches $2.64 For 5.5 HP newer Sears mowers. Fits Tecumseh models: LEV100, LEV115, LEV120, OVRM105, OVRM65, TVS115 & TVS120. Poly bagged.Length: 2-3/4" Width: 1-3/4" Height: 2-7/8" Home Improvement... |
|
|
BRIGGS STARTER 14 TOOTH Steel Gear 693551, 693552 $45.95 ... |
|
|
CARBURETOR CARBURETOR REPL TECUMSEH 632615 $34.95 Carburetor replaces Tecumseh 632615. Fits H30, H35. Replaces: TECUMSEH 632615... |
|
|
Helicoil 5334-14 Save-A-Thread Thread Repair Kit M14 x 1.25 $42.20 The only thread repair product that can be used to repair both taper seat and gasket type spark plug assembliesThree insert lengths are available to accommodate all spark plug reachesPositive mechanical locking feature means the insert will never come out! The piloted reamer tap means no drilling is necessary and perfect alignment of the tapped holeAvailable in kit or set for the do-it-yourselfer ... |
|
|
MTD Part 753-04039 HARN:WIRE:SAF:SW [Electronics] $7.65 Check your Owners/Parts manual for correct application and fit. This is the current part description provided by the Original Equipment Manufacturer (OEM). To confirm your parts fit or description, Email us with your Make, Model and Serial Numbers.... |
|
|
Sears Craftsman AYP EHP Part 83700 Cable Clamp $2.15 Check your Owners/Parts manual for correct application and fit. This is the current part description provided by the Original Equipment Manufacturer (OEM). To confirm your parts fit or description, Email us with your Make, Model and Serial Numbers.... |
|
|
John Deere LT133 Lawn Tractor OEM Service Manual $129.95 Our John Deere LT133 Lawn Tractor OEM Service Manual is a brand new original OEM (Original Equipment Manufacturer) manual for this machine. Tractor OEM Service Manuals (tractor shop manual / repair manual) provide detailed service and repair information for your tractor, with step-by-step instructions on how to repair your farm tractor or other machine. Pick one up today and save yourself time and... |
|
|
John Deere 110H Lawn & Garden Tractor (SN 0-100 000) OEM Parts Manual $39.95 Our John Deere 110H Lawn & Garden Tractor (SN 0-100 000) OEM Parts Manual is a brand new original OEM (Original Equipment Manufacturer) manual for this machine. Tractor OEM Parts Manuals outline the various components of your tractor and offer exploded views of the parts it contains and the way in which they're assembled. At the end of the day, you'll want to know exactly what parts you'll need an... |
